DIN EN 300, “OSB – Classification and requirement definitions”
The standard defines the OSB as consisting of long, narrow, justified filings. The top layer filings are oriented square with the substrate layer. The filings in OSB are bound with different binding agents such as PF adhesives, PMDI adhesives, melamine or urea resins, formaldehyde-tannin resins, and urea-formaldehyde resins. In accordance with DIN EN 300, types OSB 1 - OSB 4 are divided based on intended purpose as follows: The higher the count, the higher quality and more durable the product is.
The definitive classes for floor covering and wood flooring work are:
- OSB/2: Tiles for supporting purposes for use in dry areas, manufacturing of packaging material
- OSB/3: Tiles for supporting purposes in wet areas
- OSB/4: Highly durable tiles for supporting purposes for use in wet areas
DIN EN 634/2, “Cement-bound chipboards”
This standard defines cement-bound tiles as being chiefly made of conifer wood shavings, Portland cement, and additives like hemp or flax (FBP). These tiles are already sanded at the factory and equipped with groove/spring. Their high dead weight and difficult workability are detrimental.
Installation of floor covering
Virtually all types of textile and resilient floor coverings, as well as wood flooring, can be installed on pre-made composite wood board screed constructions. This includes:
- Textile floor coverings
- Resilient floor coverings
- Cork floor covering
- Multi-ply wood flooring
- Solid wood flooring/solid boards
- Design interlocking covering
- Loose lay = loose laid floor coverings with base tie-in
There are limitations in installation for heavy wood flooring (minimum thickness). It is not recommended to install ceramic tiles and natural stone on this kind of pre-made screed construction!
Types of construction for flooring structures with chipboard and OSB
Chipboard or OSB are used in three different constructions in normal building practice:
1. Floating installation of tiles in one- or two-ply design (precast screed construction)
With floating installation, it’s especially important to pay attention to moisture protection, avoiding cross joints, edge distance, a professionally prepared substrate, and minimum thickness. This means that a moisture-barring film will be installed on the supporting substrate and the wood moisture adjusted to the manufacturer's recommendation. Cross joints must be avoided at all costs, and the tiles will be installed with the top side facing up (see below). The edge distance to adjacent components must be at least 10 mm! If groove-and-tongue tiles are used, please make sure that the joints are hammered down correctly and dense. For a two-ply tile installation, watch that the tiles do not mismatch each other by more than 1/3 to 1/4 of the length of the element. In addition, they must be adhere correctly and screw-fixed or clamped into the screen to make sure of the bond. The two-ply installation of tiles prevents the individual tiles from showing under the floor covering to be installed later. This defect can occur fairly easily in one-ply installation.
2. Construction on joists or battens/sleepers
When installing on joists or battens, pay attention to the centre-to-centre distance of the timbers, the moisture protection in the construction design, and adequate edge distance. This means that the clear span of the joist should be about 40 cm each and not exceed 50 cm. The construction should be ventilated from below to avoid damage from condensation. The tile thickness must be measured so that the envisaged levels of traffic can be safely absorbed. A film must be applied to the joist to protect against creaking. This goes without saying, but is often done incorrectly: The tiles must be installed with the correct side, labelled as such, facing up.
3. Setting the tiles on the existing floorboard constructions
When setting tiles on an existing floorboard construction, it’s important to make sure that the beam construction is ventilated from behind. Will be screw-fixed in the screen (30 cm x cm/40 cm x 40 cm). A mix of bonding and screw-fixing can also be used as an alternative. The end joins will be fine-tuned to a distance of about 10-15 cm! Even if protection against creaking (film) has been installed, noises may occur. The client should be informed about this. It’s important that the construction as a whole is sufficiently bend-proof for the anticipated traffic loads. Make sure there is adequate edge space, as with all types of construction.
Complaints and their causes
If chipboard and OSB are not installed conforming to standards, this can lead to complaints later on. What does this look like? How can they be prevented?
- Board joints showing: The cause here is usually a one-ply chipboard installation, or the tongue/groove areas haven’t been glued enough. Often, there is no sufficient rear ventilation.
- Warping of floor covering or even the entire construction: Usually the edge distances or the edges areas are spackled in such a way that ventilation from behind is not guaranteed.
- Bulging and bubbling of the adhered/installed floor coverings: The reason for this is that the wrong primer has been used, and the levelling compound is breaking away with the floor covering as a result.
- Creaking of the substrate/wooden composite boards: The cause is often wood-on-wood construction. A film to prevent creaking must be installed between the joist and the board.
- Odour/mould formation: This occurs due to interactions with the binding agent used on the chipboard or OSB, or with old adhesives.